RESIN epoxy liquid with HARDENER
A composition of modified epoxy resins with low viscosity. Used as component No. 1 in a two-component system (component No. 1 – resin, component No. 2 – hardener) designed for pouring up to 5 cm. It is also used as a two-component filling compound for industrial and decorative coatings, floors, fixing fibreglass, veneer, top coat, etc.
EPOXY RESIN FOR HANDWORK AND FILLING, “TOP COAT”.
A composition of modified epoxy resins with low viscosity.
A composition of modified epoxy resins with low viscosity. Used as component No. 1 in a two-component system (component No. 1 – resin composition, component No. 2 – hardener) designed for filling up to 5 cm. Also used as a two-component filling compound for industrial and decorative coatings, floors, fixing fibreglass, veneer, top coat, etc.
PROPERTIES:
- Transparent with UV protection against yellowing;
- Good adhesion to various surfaces;
- Reduced bubble formation;
- High strength;
- Short curing time;
- Good fluidity – self-levelling;
- Resistant to chemical reagents.
APPLICATION: The surfaces to be treated must be clean, solid and slightly rough. Surface moisture content must not exceed 10% (wood 5%). Apply to concrete surfaces no earlier than 28 days after laying the concrete. Minimum application temperature +15°C. Components No. 1 and No. 2 must be thoroughly mixed in a weight ratio of 100:23. Tools and equipment must be washed immediately after use with an acetone-based solvent.
DRYING TIME: Initial setting time is 30 to 60 minutes at room temperature. Full curing time is approximately 24-60 hours at room temperature, depending on the thickness of the pour. STORAGE: Store in the original packaging at a temperature between +5°C and +25°C. The shelf life is indicated on the packaging.
RESIN (component No. 1):
Hazard categories: Skin Irrit. 1
Skin. Sens. 1
Eye Irrit. 2
Aquatic Chronic 2
Signal word: Warning
Contains: 4,4′-isopropylidenediphenol, oligomer reaction product with 1-chloro-2,3-epoxypropane (average molecular weight ≤ 700), oxirane, mono[(C12-14-alkyloxy)methyl] derivatives, benzyl alcohol
Product exposure characteristics: H315 – causes skin irritation
H317 – may cause an allergic skin reaction
H319 – causes serious eye irritation
H332 – harmful if inhaled
H411 – toxic to aquatic life with long-lasting effects.
Safety requirements: P262 – Avoid contact with eyes, skin or clothing.
P273 – Avoid release to the environment.
P280 – Wear protective gloves/protective clothing/eye protection/protective mask.
P302 + P352 IF ON SKIN: Wash with plenty of soap and water.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Additional labelling: –
HARDENER (component No. 2):
Hazard categories: Acute tox.4
Skin corr.1B
Eye dam.1
Skin sens.1
Aquatic chron.3
Signal word: Danger
Contains: Isophorone diamine (3-aminomethyl-3,5,5-trimethylcyclohexylamine), benzyl alcohol
Product exposure characteristics: H302-Harmful if swallowed;
H312-Harmful in contact with skin;
H314-Causes severe skin burns and eye damage;
H317-May cause an allergic skin reaction;
H318-Causes serious eye damage;
H412-Harmful to aquatic life with long-lasting effects.
Safety requirements labelling: P280 – Wear protective gloves, protective clothing, eye protection and protective masks;
P301+P330+P331 – IF SWALLOWED: Rinse mouth. Do not induce vomiting.
P303+P361+P353 – IF ON SKIN (or hair): Remove all contaminated clothing immediately. Rinse skin with water/shower.
P305+P351+P338 – IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P310-Immediately call a POISON CENTRE or doctor/physician.
P501-Dispose of contents/container in accordance with local regulations.
Additional labelling: –
